Wheels

No words needed. Just google "EX 471 Leogang World Cup". Let your muscles play on the uphills and switch to attack mode for the downhills. This is exactly what the DT Swiss Enduro rims are made for. Each rim is a piece of high precision engineering and, thanks to the extremely resistant alloy, the EX 471 can cope with the most demanding trails.

The updated team favorite, FX2 freecoaster hub. Featuring proven KHE based internals, a 9T dual-sealed bearing driver with additional bushing, and a super-strong heat-treated Chromoly 14mm axle with 6mm internal hex for easier maintenance. Updated with the DTC system, changing drive side only requires a driver change instead of a whole hub replacement. Slack can be adjusted from 55 degrees up to 180 degrees depending on your preference, and ships with 156 degrees slack as standard. The included nylon CR and DR hub guards keep your hub protected from grinds straight out of the box. - 9T Freecoaster - Axle: 14mm Hollow Heat-Treated Chromoly - Axle Nuts: 17mm Chromoly - Shell: 6061-T6 Aluminum 36-hole - Bearings: 1 x 6002, 1 x 7905, 2 x 6902 + Bushing - Clutch: DTC (Dual Threaded Clutch) - Cones: Threaded Drive Side and Non-Drive Side - Guards: Compatible with Cinema DR and CR hub guards - Slack: Includes 3 Slack Washer For Fine Tuning - Weight: 25.3oz (w/Guards Installed)

The Mission Engage rear cassette wheel is a fully sealed hub, 3-cross laced to the rugged Mission Mylar double wall rim. Heat-treated chromoly axle, 5 precision sealed bearings, and stainless-steel spokes make the Engage wheel a solid ride. - Hub: Mission Engage Cassette - Rim: Mission Mylar - Weight: 46.1oz

A pair of steel axle nuts. - 17mm wrench flats

A pair of lightweight, 17mm aluminum axle nuts. - 14mm fits most rear axles (M14xP1.0) - 3/8" fits most front axles (3/8x26T) - 7075-T6 aluminum - Weight: 0.8oz

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: JoyTech, Joy U, KK 9mm x 1, front hub - Compatible with 9mm x 1 axle - Cone Wrench Size: 15mm - Threads: 9mm x 1 - Diameter: 15.0mm - Length: 12.8mm - 1 cone per bag - Note: O-ring / seal not included. COMPATIBLE HUBS: - JoyTech, Joy U, KK 9mm x 1, front hub - Taiwanese front hubs with 9mm x 1 axle

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: JoyTech 10mm x 26, rear hub - Compatible with 10mm x 26 axle - Cone Wrench Size: 15mm - Threads: 10mm x 26 - Diameter: 17.0mm - Length: 13.8mm - Note: O-ring / seal not included. - 1 cone per bag COMPATIBLE HUBS: - JoyTech 10mm x 26, rear hub - Taiwanese hubs with 10mm x 26 axle

- Designed, tested, and raced to victories on the World Cup DH and Enduro World Series circuits - Tie beam triple-cavity rim design resists damage and prevents air loss under impacts - 29mm internal width optimized for 2.35" to 2.8" Trail, All-mountain, and DH tires - E-sync hubs

- Low-profile 30mm internal width optimizes tire shape, traction, and control for 2.3-2.6" tires - Durable 6069 aluminum with welded joint and reinforced spoke bed - BST Asymmetric design combines Stan's legendary easy tubeless inflation with a stronger, more balanced wheel build - Reinforced spoke bed, combined with the offset drilling of the asym design, builds into an incredibly durable wheel that brings added confidence to every ride.

Based on the legendary Flow EX, the new Flow EX3 rim features Tiebeam, an internal reinforcement that offers unmatched impact resistance and the best air retention of any tubeless rim. The Flow EX3 combines the incredibly durable Tiebeam design of Stan's classic Flow EX with the 29mm internal width and 6069 aluminum construction of the popular Flow MK3 to create an entirely new rim built to handle today's faster, heavier and more capable enduro, downhill and e-bikes. - Designed, tested, and raced to victories on the World Cup DH and Enduro World Series circuits - Tie-beam triple-cavity rim design resists damage and prevents air loss under impacts - 29mm internal width optimized for 2.35" to 2.8" Trail, All-mountain, and DH tires

The Arch MK4 is the wheelset a lot of us here at Stan's choose to ride. All-mountain, Downcountry, Trailduro—whatever they're calling it this week, when you like pushing your limits on climbs, descents, and every kind of trail, this is your wheelset. The Arch MK4's 28mm internal width and patented lightweight, low-profile design is not afraid to climb, while being an absolute monster on the descents. With a welded seam, reinforced spoke bed, and durable 6069 aluminum construction, the Arch MK4 rims give you the confidence to ride everything. When it comes to a consistent and reliable airtight tubeless seal, nothing beats Stan's patented Bead Socket Technology. The Arch MK4 rims feature an asymmetric design with offset spoke holes to improve spoke angle and create a stronger all-around wheel. Unlike most asymmetric rims that suffer from difficult inflation and poor tubeless performance, Stan's BST-Asymmetric design delivers all the advantages of a stronger wheel, with no compromises in tubeless performance. Nobody likes downtime, so the Arch MK4 wheelset is built with traditional J-bend spokes based on their proven strength, ride quality, and easy serviceability. Stan's has always made it easy to find replacement spokes should you ever damage your wheel, and now we've made it even easier. MK4 front and rear wheels of the same diameter all use the exact same very common spoke length, both sides, front and rear. Serviceability doesn't get any easier than that. From the first click of the incredible M-pulse hubs, it's clear that confidence is the philosophy behind every part of this wheelset. Designed and CNC machined by Project321 in Bend, Oregon, M-pulse freehubs feature 6 pawls with Neodymium magnets that lock into place with greater force than conventional pawl springs, but offer virtually no resistance when coasting. Multiple teeth on each pawl offer better load distribution for years of trouble-free riding, and the angle of the pawls was engineered to transfer stress away from the rotating bearings, decreasing stress and wear on the entire freehub. That durability extends to the 17mm axles machined of 7075 aluminum and the full complement of Enduro brand bearings, including a double-row freehub bearing. M-pulse internals are also fully shielded inside the hub, because the only thing better than a good bearing seal is a good bearing seal most dirt can't even reach. As durable as they are, these hubs are also built for speed. M-pulse hubs engage with only 1.66°of rotation, putting down power nearly instantaneously, but how smooth these hubs roll is what really stands out. Adjustable preload allows you to fine tune M-pulse hubs for reduced friction, and less drag means more speed on the ground.The result is a bombproof hub with quick, consistent engagement and less resistance for more speed. Available with Shimano Micro Spline, HG, or SRAM XDR freehub, and 6-bolt or Centerlock brake style, with options to fit all popular axle configurations. Tubeless ready with rim tape installed. The Arch MK4 is our most versatile wheelset, and the best aluminum wheelset available for riders who want to push limits on every trail. Up, down, and wherever the ride takes you, the Arch MK4 wheelset has it under control. - Arch MK4 wheels include pre-installed tape for tubeless use and presta valves. - Versatile 28mm internal rim width optimized for 2.2-2.5” tires - Light and durable 6069 aluminum with welded joint and reinforced spoke bed - BST-Asymmetric design combines Stan’s legendary easy tubeless inflation with a stronger, more balanced wheel build - M-pulse ultra-low drag magnetic pawl adjustable hubs with 1.66° engagement - Enduro bearings with double-row freehub bearing - Matched wheelsets use traditional J-bend lacing and share a single spoke length for easy serviceability - Connection program includes 5-year hub warranty, 3-year rim warranty, 1-year crash replacement, and $10 donation to trail maintenance or advocacy group of your choice

- Position Front - Wheel Diameter/ISO 700C / 622 - Axle Type QR - Hub Spacing 100mm - Wheel-Brake Comp. Rim - Freehub Body - - Wheel Tire Type Clincher - Rim Material Aluminum - Rim Construction Double wall - Rim Internal Width 18.4mm - Rim inner width range 0-21.9mm - Rim Color Silver - Rim Drilling 36 - Hub Model Formula FM-21-QR - Wheel Weight - - Spoke Type Stainless - Valve Schrader - Rim External Width 24.4mm - Depth 16mm - Rim Model Alex DM18 - Skewers Included Yes

- Position Rear - Wheel Diameter/ISO 700C / 622 - Axle Type Bolt-on - Hub Spacing 135mm - Wheel-Brake Comp. Rim - Freehub Body Freewheel - Wheel Tire Type Clincher - Rim Material Aluminum - Rim Construction Double wall - Rim Internal Width 18.4mm - Rim inner width range 0-21.9mm - Rim Drilling 36 - Hub Model Formula FM-31 - Wheel Weight - - Spoke Type Stainless - Valve Schrader - Rim External Width 24.4mm - Depth 16mm - Rim Model Alex DM18

- Kits include one pair of end caps - Instructions and hub axle determinations are available online @ www.notubes.com

Rims: WTB CZR i23 Carbon 700C - ETRTO 622-23 - Inner width: 23mm - Torayca T700 UD carbon fiber for stiffness and compliance - Asymetric and angled spoke hole drilling - Externally reinforced spoke bed - Drilled for Presta valve - TCS 2.0 Tubeless System compatible - 28 holes Front hub: Shimano HB-RS770 Ultegra series - 12x100mm E-THRU (Axle not included) - Center Lock (6-Bolt adapter included) - Polished angular contact bearings - Contact sealed hub Rear hub: Shimano FH-RS770 Ultegra series - 12x142mm E-THRU (Axle not included) - Center Lock (6-Bolt adapter included) - Polished angular contact bearings - Contact sealed hub and freehub body - Compatible with 11 speed Road (10 speed compatibility requires 1.85mm spacer, not included) Sold in Pair, including: - Tubeless Valve (x2) Assembled in North America by experienced wheelbuilders with Sapim Race Butted Stainless Steel spokes (Black) and 14mm Brass Polyax Nipples

Whether the goal is a finish line, epic adventure or simply getting back home again, SRAM'S 900 hubs are ready for the challenge. On the inside, the smooth and durable DOUBLE TIME drive mechanism ensures rapid engagement for quick and confident pedal responsiveness. SPEEDBALL bearings provide smooth, long-lasting rotation performance. Multiple spoke-count and cassette-capability options, as well as interchangeable end caps, make the 900 hubs a perfect choice for any disc-equipped road, gravel, cyclocross, cross country, trail, or enduro bike. - Versatile driver body can accept ROAD or MTB drivetrain, full spline or XD cassettes - Fully convertible with tool-free end caps - BOOST variants - 24, 28 or 32 spoke holes

Whether the goal is a finish line, epic adventure or simply getting back home again, SRAM's 900 hubs are ready for the challenge. On the inside, their smooth and durable DOUBLE TIME drive mechanism ensures rapid engagement for quick and confident pedal responsiveness. SPEEDBALL bearings provide smooth, long-lasting rotation performance. Multiple spoke-count and cassette-capability options, as well as interchangeable end caps, make the 900 hubs a perfect choice for any disc-equipped road, gravel, cyclocross, cross country, trail, or enduro bike. - Fully convertible with tool-free end caps - 24, 28 or 32 spoke holes

Rims: Alex AT490 700C - ETRTO 622-17 - External width: 22mm - Inner width: 17mm - Profile height: 24mm - CSW Machined Sidewall - TRS Tubeless Compatible - For Presta valve - 32 holes Rear hub: Shimano Tiagra FH-RS400 - 10x130mm - Polished angular contact bearings - Contact sealed hub and freehub body - Quick Release Binder (Internal Cam) included - Compatible with 11 speed Road (10-speed compatibility requires 1.85mm spacer, not included) Assembled in North America by experienced wheel builders with Sapim 14G Stainless Steel spokes (Black) and 14mm Brass Polyax Nipples (Black).

- Low-profile 30mm internal width optimizes tire shape, traction, and control for 2.3-2.6'' tires - Durable 6069 aluminum with welded joint and reinforced spoke bed - BST Asymmetric design combines Stan's legendary easy tubeless inflation with a stronger, more balanced wheel build - Reinforced spoke bed, combined with the offset drilling of the asymmetrical design, builds into an incredibly durable wheel that brings added confidence to every ride. Specs: - Rim Material: Aluminum - Rim Eyelets: No - Valve: Presta - Rim Construction: Double wall - Brake Type: Disc - Tire Type: Tubeless Ready

- Position Rear - Wheel Diameter/ISO 26'' / 559 - Axle Type QR - Hub Spacing 135mm - Wheel-Brake Comp. Rim and Disc IS 6-bolt - Freehub Body Shimano HG - Wheel Tire Type Clincher - Rim Material Aluminum - Rim Construction Double wall - Rim Internal Width 18.4mm - Rim inner width range 0-21.9mm - Rim Color Black - Rim Drilling 36 - Hub Model Shimano FH-M475 - Wheel Weight - - Spoke Type Stainless - Valve Schrader - Rim External Width 24.4mm - Depth 16mm - Rim Model Alex DM18 - Skewers Included Yes

- 3-piece kit to secure wheels and seatpost - Lighter and safer than regular QR skewers - MTB 100mm/135mm - Seatpost: M6 x 45mm

- CNC machined alloy locking end nut - Cr-Mo axle construction - Patented hollow hex key anti-theft security - Fits most City, MTN and Hybrid bikes (100mm/135mm) - Lightweight and compact design - 85g (Pair)

Champion 2.0 Black Spokes - One 264mm spoke = 7g

Ease of use, lightweight, and optimum performance in a single product. The DT Pro Head shape, combined with both a torx and a square tool interface, makes wheel building a lot easier. The spherical contact surface aligns the nipple perfectly with the spoke. All-brass nipples are recommended for e-bike use. Weight: starting at 26g for 64 nipples.

- Skewer Trek QR-18 100mm Bolt-On Front Black - Skewer Trek QR-18 135mm Bolt-On Rear Black

- A high performance alloy rim designed for freeride, race and downhill use - Tubeless ready with anti-burp rim hooks to prevent the loss of pressure and keep tires firmly in place - 32 holes with an inner width of 28mm and outer width of 33mm to optimize tire spread and enhance traction - The corrugated rim center, a brand acclaimed technology, adds exceptional strength, making it more rigid and allowing the rim to be wider without adding material - Shotpeen finish to increase fatigue life and make it more durable

This is one of the most versatile spokes in the DT Swiss spoke range. DT competition gets its special strength from cold forging. This makes an extremely durable spoke and thanks to the thinner middle section, it is 48 g lighter (per 64 spokes) than a spoke with a constant diameter of 1.8 mm. It is perfect for a wide range of uses, from road wheels to super light enduro MTB wheels. - Double Butted: 2.0/1.8/2.0 - One 264mm spoke = 6g - Nipples sold separately

Developed for short spokes with a large deflection angle. DT Pro Head nipples are designed for short spokes with a large angle of deflection, such as for e-bike use. Through the spherical contact surface, the nipple aligns automatically with the angle of the spoke, which leads to consistent power transmission. Note: brass nipples are not approved for children's products in the USA. See attached warning! All-brass nipples are recommended for e-bike use. - Weight: starting at 59g for 64 nipples.

This is one of the most versatile spokes in the DT Swiss spoke range. DT competition gets its special strength from cold forging. This makes an extremely durable spoke and thanks to the thinner middle section, it is 48 g lighter (per 64 spokes) than a spoke with a constant diameter of 1.8 mm. It is perfect for a wide range of uses, from road wheels to super light enduro MTB wheels. - Double Butted: 2.0/1.8/2.0 - Compatible with straight pull hubs only - One 264mm spoke = 5.9g - Nipples sold separately

EX 1700 SPLINE wheels feature a super strong and welded 30 mm wide aluminum rim with a profile design made to withstand the hardest use of Enduro racing, while still keeping the weight low for long and demanding uphills. Laced to double butted competition straightpull spokes, the EX 1700 SPLINE wheels are built to take a beating. - Welded Aluminum rim with 30mm internal width - 350 hub with 36 point SL Ratchet system - Competition spokes and Squorx nipples - Designed for Enduro applications

Machined aluminum spacers for freehubs. Great for fine tuning freewheel and cassette placement or improving chainline. Also good for bottom bracket spacing with BSA BB cups. - Inner Diameter: 35.0mm - Outer Diameter: 40.7mm - Material: Aluminum - Finish: Polished - Bags of 10

- Evo Tour 19 26" double wall rim - Black - Rim and Disc - Inner Rim Width: 19 mm - Rim Height: 20 mm - Pin joint construction - No Eyelets - Schrader valve - 36 holes - Stainless steel spokes - Silver

Zipp's 303 Firecrest Tubeless wheels are designed for the real world—a world of imperfect conditions, varying road surfaces, and elements where the bottom line is simple: efficiency = speed. They're faster, lighter, and more capable over varied terrain—whether the surface is pavement in all its conditions or no pavement at all. Deeply rooted in Zipp's drive to conquer the Spring Classics, the new 303 Firecrest is remade with a purpose-made approach for the demands of modern road bikes. When it comes to going fast on a bicycle, efficiency means reduced wind resistance, rolling resistance, rider fatigue, and weight. The 303 Firecrest Tubeless Disc-brake was designed using real-world direct measurements (vs. primarily wind tunnel or computer simulation). The results were huge. Its rim is slightly more bulbous in design than its predecessor, with a 32mm outside width, a 25mm internal width, and a 40mm rim depth. The profile provides low drag and an improved transition between rim and tire, boosting aero efficiency on the road. The wide rim stance also features less tire deflection for reduced rolling resistance. The combination of the wider tire, increased tire volume, and lower tire pressure helps to reduce rider fatigue by smoothing out the ride over imperfect pavement and road conditions—the tire and wheel system absorbs the shaking, not the rider. At the center of the 303 Firecrest Tubeless is a versatile and durable new hubset, the German-engineered ZR1 DB. This hubset features 66 points of engagement for quicker response. The 303 Firecrest Tubeless wheels are for dedicated cyclists who aspire to the latest in technology. They're for those who compete in races, against peers, or simply to conquer personal limits. - New Zipp graphics and cosmetic identity that scream speed - Versatile endurance wheelset for the modern road bike with tubeless and hookless rim profile - Lighter weight than its predecessor, making it nimble and fast - Tubeless Made Easy, optimized tire bed sign allows for simple tool-free installation and removal with no need for an air compressor to seat the tire. - Ultra-wide 25mm rim profile creates a better tire interface to be fast on or off the road - 40mm rim depth makes a light and aero wheel in every situation - Ships with 12mm end caps - Center Lock rotor interface (lockring included)

- Grade 3 balls and magnetite rust proof finish - Abec 5 precision and silicone w seals - 3 times cryogenic race treatment - Bearings sold individually, not as pair

- Asymmetric Bead Socket Technology brings Stan's legendary easy inflation and the most reliable airtight seal to wider, offset carbon rims - Custom carbon layup equalizes impact forces on both the long and short sides of the rim, making both stronger - Asymmetric rim shape with offset drilling improves bracing angle and balances spoke tension to create a stronger overall wheel - M-pulse hubs - 250lb Recommended Maximum Rider Weight

Stan's lightweight aluminum valve stems are half the weight of Stan's standard brass valves. The secure round base is compatible with most tubeless rims and a perfect fit for all Stan's BST rims. A removable valve core makes adding sealant easy, and these babies fit up to 8mm valve hole. Sold as a pair.

- Laced with Sapim Laser triple-butted spokes and mechanically locking alloy nipples. - M-pulse Hub - RiACT system absorbs impacts and rolls faster - Bead Socket Technology for unmatched tubeless performance - WideRight rim design optimized for 2.00"-2.25" XC and Trail tires

- Hub axle, front - Zipp Cognition V2 Disc Brake (axle & wave spring)

Rims: EVO JP95 27.5" - ETRTO 584-94 - Inner width: 94mm - Disc Brake Only - Drilled for Schrader valve - 32 holes Front hub: Novatec D201SB - 15x150mm (Axle not included) - 6-Bolt Disc Mount - Sealed cartridge bearings (x2) Assembled in North America by experienced wheelbuilders with Sapim stainless steel spokes (Black) and 14mm Brass Polyax Nipples (Black)

- Zipp's most advanced and fastest deep-rim wheel for road, triathlon, and time trialing - More than 300 grams lighter that previous model - Optimized tire bed for easy tire installation - Sawtooth rim with Hyperfoil nodes and HexFin ABLC dimple pattern for top aero and crosswind-stability performance with an undulating rim depth - Cognition V2 hubset rolls efficiently whether you are pedaling or coasting. Its Axial Clutch V2 technology reduces drag and lowers friction - Center locking rotor interface. Lockring is included with the wheels - Zipp graphics applied using Zipp's ImPress direct-print technology - Minimum 25mm tire width - Lifetime Warranty

- Replacement freehub bodies include pawls and springs pre-installed - M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg - E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls - HG 11sp road FH body

- Replacement freehub bodies include pawls and springs pre-installed - M-Pulse hubs: six pawls are equipped with Neodymium magnets engaging every 1.66 deg - E-Sync hubs: fast 8.18 deg engagement with reinforced high-torque pawls - HG 11sp road FH body

- Position Front - Wheel Diameter/ISO 26'' / 559 - Axle Type QR - Hub Spacing 100mm - Wheel-Brake Comp. Rim - Freehub Body - - Wheel Tire Type Clincher - Rim Material Aluminum - Rim Construction Double wall - Rim Internal Width 18.4mm - Rim inner width range 0-21.9mm - Rim Color Black - Rim Drilling 36 - Hub Model Formula FM-21-QR - Wheel Weight - - Spoke Type Stainless - Valve Schrader - Rim External Width 24.4mm - Depth 16mm - Rim Model Alex DM18 - Skewers Included Yes

A tough, tubeless-compatible 27.5 disc wheelset in new-school boost thru-axle spacing. - Pinned construction double wall rim with new-school 29mm internal width, tubeless compatibility, offset/asymmetrical construction, and hook-less construction - Asymmetric rims w/ offset spoke holes for better triangulation of spoke angles and balance of tensions in a wheel build, resulting in a stronger, stiffer, and more reliable wheel - Joytech Boost thru-axle alloy 6-Bolt hubs w/ serviceable cup and cone bearings - Shimano steel freehub: 8/9/10/11sp MTB compatibility - 6-Bolt disc compatible only - Reinforced head plain gauge 14G/2.0mm Stainless Steel spokes (black) w/12mm brass nipples (black) - 32H/3X lacing - Presta drilling - high-pressure rim tape included (non-tubeless) - Tubeless compatible - Weight: Front - 1076g, Rear: 1177g

A tough, tubeless-compatible 27.5-inch disc wheelset in traditional non-boost thru-axle spacing. - Pinned construction double-wall rim with new-school 29mm internal width, tubeless compatibility, offset/asymmetrical construction, and hookless construction - Asymmetric rims w/offset spoke holes for better triangulation of spoke angles and balance of tensions in a wheel build, resulting in a stronger, stiffer, and more reliable wheel - Joytech thru-axle alloy 6-Bolt hubs w/serviceable cup and cone bearings - Shimano steel freehub: 8/9/10/11sp MTB compatibility - 6-Bolt disc compatible only - Reinforced head straight gauge 14G/2.0mm Stainless Steel spokes (black) w/12mm brass nipples (black) - Weight: 1191g

Tough-yet-affordable single wall rear 18-inch (355mm ISO) coaster wheel that uses a much higher build standard and materials than many original factory-equipped wheels. - Alex Y303 pinned construction single wall rim with 24mm internal width for an excellent pairing with modern high-volume tires - Anodized brake track for clean looks when used with coaster only - KT 305R Nutted 110mm OLD steel coaster hubs w/serviceable cup and cone bearings - Compatible w/3-spline coaster hub sprockets, 16T included - Straight gauge 14G/2.0mm Stainless Steel spokes (black) w/12mm brass nipples (silver) - Weight: 1213g

The ZX 333 front wheel is our most affordable wheel. Featuring our double-wall pin-joint 333 rim, laced 3x to a fully sealed hub with a female axle with 3/8" bolts. All Cinema wheels come with a Cinema rim strip and Cinema hub guards! - Hub: Cinema ZX - Rim: Cinema 333 - Spokes: 36 stainless steel - Weight: 2 lbs 5 oz

The CF front hub guard presses directly over existing Cinema hub hardware to protect your hub and spokes on grinds. Injection molded from super durable nylon material, this guard can handle some serious abuse while still being affordable. - Material: Nylon - Fits: Cinema FX, VX2 and ZX Front Hubs and Wheels (2017 and later) - Side: Either Side - Weight: 0.9 oz

Designed for the non-drive side, the CR rear hub guard presses directly over existing hub hardware to protect your hub and spokes. Injection molded from super durable nylon material, this guard can handle some serious abuse while still being affordable. - Material: Nylon - Fits: Cinema FX & FX2 Freecoaster; VX2, VX3, and ZX Cassette Hubs and Wheels (2017 and later) - Side: Non-Drive Side - Weight: 1.3 oz

Hand-built to A-Class specifications, the 350 wheels with SPANK Hex Drive hub is the premium lightweight performance offer from the SPANK wheelhouse and is trusted by pros on the Enduro World Series circuit. - Unique profile with low sectional height & wide width adds radial compliance & lateral stiffness - Improved radial compliance for better traction over bumps & chatter while reducing negative feedback to the rider gives enhanced performance & comfort - 30mm internal width is versatile, fitting tires from 2" to 2.6" and allows plus-size tire use without negative squaring off of tire profiles

- Durable six series alloy rim suitable for kids bikes or 24" street bikes - 32 holes with an inner width of 23 mm and outer width of 28mm - The corrugated rim center adds exceptional strength, making it more rigid and allowing the rim to be wider without adding material - Shotpeen finish increases fatigue life and durability - Ultra-strong, ultra-safe option at a value oriented price - RECOMMENDED FOR: ASTM 4, All mountain, free ride - RIDER TYPE: MEDIUM TO LIGHT RIDER: Medium to Light Impact - HUB: SPANK SPOON Front Hub (2021) - HOLE COUNT: 32 - SIZES (inches): 24 - WEIGHT +/- (g): - INNER WIDTH (mm): 23 - OUTER WIDTH (mm): 28 - PROFILE HEIGHT (mm): 24 - ETRTO: 507x23 - ERD++ (mm): 474++ - TUBELESS: Not recommended - VALVE: A/V Shrader - TIRE FIT: 1.3" to 2.3" - FEATURES: OohBah Inverted Inner Wall, MGR 6 Series Alloy ++: SPANK ERD = Rim diameter (mm) with 2x spoke bed thickness (mm) included. (++) = add your own nipple head height in mm x

Rims: WTB ST i23 24" - ETRTO 507-23 - Inner width: 23mm - Disc Brake Only - Drilled for Presta valve - TCS 2.0 Tubeless System compatible - Solid Strip (included) - 32 holes Front hub: Shimano HB-MT400-B Boost - 15x110mm (Axle not included) - Center Lock (6-Bolt adapter included) - Angular contact bearings - Contact sealed hub Assembled in North America by experienced wheelbuilders with Sapim stainless steel spokes (Black) and 14mm Brass Polyax Nipples (Black)

A tough, no-nonsense workhorse 27.5-inch rim brake wheelset with MTB hub spacing that's perfectly suited to a wide range of applications from MTB to urban/commute/trekking. - Pinned construction double-wall rim with generous 20mm internal width suitable for a wide range of tire widths - Stainless Steel eyelets & CNC machined sidewall w/wear indicator - Joytech alloy QR hub w/serviceable cup and cone bearings - Reinforced head straight gauge 14G/2.0mm SUS304 Stainless Steel spokes (black) w/12mm brass nipples (silver) - Weight: 974g

A tough, no-nonsense workhorse 29/700c rim brake wheel with MTB hub spacing that's perfectly suited to a wide range of applications from MTB to urban/commute/trekking. - Pinned construction double-wall rim with generous 20mm internal width suitable for a wide range of tire widths - Stainless Steel eyelets & CNC machined sidewall w/wear indicator - Joytech alloy QR hubs w/serviceable cup and cone bearings - Reinforced head plain gauge 14G/2.0mm SUS304 Stainless Steel spokes (black) w/12mm brass nipples (silver) - Not tubeless compatible - Weight: 1027g

Replacement 12x100 Adapters for HEX 28 Gravel Front Hubs. Compatible with: - HEX Gravel J-Type Front Wheels Not compatible with: - HEX Straightpull or HEX J-Type 32H Front Wheels - Boost front wheels - SPIKE/OOZY/SPOON hubs - HEX 32 J-Type or 28 Straightpull Front Hubs.

The low-profile, radially compliant alloy rim injected with SPANK's award-winning Vibrocore to add torsional strength and lateral stiffness, offers a smooth and highly responsive ride feel. Hand-built to A-Class specifications, the 359 Vibrocore wheels with SPANK Hex Drive hub is the premium offer from the SPANK wheelhouse and is trusted by pros on the UCI DH World Cup circuit, as well as big-mountain free-riders. This wheel is spec'd and built for the heavy hitters. - Moderately low 19mm profile height and wide width balances the benefits of radial compliance with high lateral stiffness and predictable handling - Radial Compliance improves traction over bumps and chatter while reducing negative feedback to the rider. Performance and comfort are improved. - Vibrocore inner well reduces the transmission of harmful vibration frequencies, meaning less vibration for the suspension and rider, also increasing the fatigue life of the rim - 30.5mm inner width is extremely versatile, fitting tires from 2.0" to 2.6", and even allowing + size tire use without negative squaring off of tire profiles - Bead Bite tubeless hooks enhance tubeless performance and tire security, even at lower pressures

Hand-built to A-Class specifications, the 350 wheels with SPANK Hex Drive hub is the premium lightweight performance offering from the SPANK wheelhouse and is trusted by pros on the Enduro World Series circuit. - Unique profile with low sectional height & wide width adds radial compliance & lateral stiffness - Improved radial compliance for better traction over bumps & chatter while reducing negative feedback to the rider gives enhanced performance & comfort - 30mm internal width is versatile, fitting tires from 2" to 2.6" and allows plus-size tire use without negative squaring off of tire profiles

- Position Front - Wheel Diameter/ISO 700C / 622 - Axle Type QR - Hub Spacing 100mm - Wheel-Brake Comp. Rim - Freehub Body - - Wheel Tire Type Clincher - Rim Material Aluminum - Rim Construction Double wall - Rim Internal Width 15mm - Rim inner width range 0-21.9mm - Rim Color Black - Rim Drilling 32 - Hub Model Shimano Sora HB-RS300 - Wheel Weight - - Spoke Type - - Valve Presta - Rim External Width 20.2mm - Depth 16mm - Rim Model Mavic Open Elite - Skewers Included Yes

A tough, tubeless-compatible 26-inch disc wheelset built around Center Lock hubs but shipped with handy 6-Bolt adapters for dual compatibility straight out of the box. - Pinned construction, tubeless-ready, asymmetric/offset double-wall rim with 24mm internal width is suited to a wide range of tire widths perfect for either MTB or urban use - Asymmetric rims w/offset spoke holes for better triangulation of spoke angles and balance of tensions in a wheel build, resulting in a stronger, stiffer, and more reliable wheel - Joytech 100mm OLD alloy QR Center Lock hub w/serviceable cup and cone bearings - Reinforced head plain gauge 14G/2.0mm Stainless Steel spokes (black) w/12mm brass nipples (black) - Weight: 926g

E-bikes add to the riding experience by simply providing more for less. More distance, more laps, more climbs, and more descents. With all those "mores" also comes more weight continually bashing on the components of an e-bike. In order to overcome the increased forces induced by the technological progression of modern e-bikes, we designed our HTZ rims with more material in every area of the rim prole. Every wall of the rim is 25-30% thicker in comparison to those on our standard rims, which we then paired with our proven I-Beam center support to ensure no beating was too great for these rims. All HTZ rims are TCS 2.0 tubeless, feature asymmetrical spoke drilling, and are available in widths ranging from i23 to i35 in order to provide options for e-bikes ranging from e-assist gravel bikes to dual-crown downhill bikes that no longer need a truck to be shuttled. FEATURES: - Capable of withstanding the forces of a modern e-bike. - 4D angled spoke drilling eliminates binding and lateral loading and disperses tension more evenly over a greater area. - Symmetric outer profile provides equal dissipation of impact forces on both sides of the rim while asymmetric spoke hole drilling allows for more even spoke tension and increased wheel strength. - Disc-brake only. - TCS 2.0 Tubeless ready and comes with a preinstalled Solid Strip, which lies beneath the tubeless tape and prevents sagging at the spoke holes, creating a smooth interface between the rim and tire bead. This prevents air from escaping around the bead and therefore requires less air volume and pressure to mount a tire. Solid Strip also protects the airtight tubeless system from being punctured in the case of a broken spoke. TCS 2.0 creates a more robust, easily installed, and dependable tubeless system. USAGE: E-bike